Marine Heat Exchanger Archives - Tipo Heat Exchangers Manufacturers, Cooling Towers Manufacturers, and Industrial Chillers Manufacturers

Evaporative Condensers in Chennai, Tamilnadu

Evaporative Condenser Introduction Evaporative condensers can replace the conventional water cooled condenser and the cooling tower. It rejects heat from a condensing vapour into the environment. ICELINGS tube ice plants can also be supplied with an Evaporative Condenser of reputed brand. They are widely used for condensing vapour in mechanical...

FRP Cooling Towers in Chennai, Tamilnadu

FRP Cooling Towers Introduction FRP Cooling Towers manufactured with Glass reinforced plastic mostly in wind with standing bottle type and square type models. It is a mechanical type Counter Flow Tower. FRP Cooling tower intakes the air from bottom and discharge the waste heat at the top. Since the water […]

Evaporative Condensers in Madurai, Tamilnadu

Evaporative Condenser Introduction Evaporative condensers can replace the conventional water cooled condenser and the cooling tower. It rejects heat from a condensing vapour into the environment. ICELINGS tube ice plants can also be supplied with an Evaporative Condenser of reputed brand. They are widely used for condensing vapour in mechanical...

Vertical shell tube heat exchangers in Ramanathapuram, Tamilnadu

Vertical Shell and Tube Heat Exchanger Introduction Vertical Shell and Tube Heat Exchanger in which the tubes extend through over sized holes in a liquid distribution plate. Liquid flows through the holes and down each tube exterior surface as a falling film. A spacer or clip, desirably of wire, is placed in each hole around […]

Kettle Reboiler Type Heat Exchanger in Salem, Tamilnadu

Kettle Reboiler Type Heat Exchangers Introduction Tipo Kettle Reboiler Type Heat Exchanger is a retaining wall or overflow weir separating the tube bundle from the reboiler section where the residual reboiled liquid called the bottoms product, bundle is kept covered with liquid. Kettle reboilers are reliable in that they can handle high...

Shell and Tube Heat Exchanger Thiruvallur, Tamilnadu

Shell and Tube Heat Exchangers Introduction Shell and tube heat exchangers consist of a series of tubes. Shell & tube heat exchangers set of these tubes contains the fluid that must be either heated. The Shell and Tube Heat Exchangers has the advantages of removability of tube bundle and access for cleaning both inner and outer […]

Oil Coolers Heat Exchangers in Madurai, tamilnadu

Oil Coolers Heat Exchangers Introduction Oil cooling refers to a process to heat displaced from a cooler oil is the principle behind oil cooler devices. The oil carrying the displaced heat usually passes a cooling unit such as a radiator, less commonly a gas decompresser. The oil cooler is connected to the lubrication system in […]

Flue Gas Air Pre Heater in Virudhunagar, Tamilnadu

Flue Gas Air Pre Heater Introduction Tipo Flue Gas Air Pre Heater of the air pre heater is to recover the heat from the boiler flue gas which increases the thermal efficiency of the boiler by reducing the useful heat lost in the flue gas.This flue gases are also sent to the flue gas stack […]

Compact Heat Exchanger in Coimbatore

Compact Heat Exchanger Introduction Compact heat exchangers transfer more energy cost-effective manner than other heat exchangers & save more energy when compared standard technology. Compact heat exchangers are to transfer heat from one fluid either gas or liquid to another. Compact heat exchangers (CHEs) have a significantly greater surface...

U tube Bundle Heat Exchanger In Chennai

U Tube bundle Heat Exchanger Introduction U Tube bundle Heat Exchanger can build “U” tube bundles, straight tube “floating” tube bundles, or we can re tube fixed tubes heat exchangers when the bundles is not removable and multitherm is not locked into any one material. Heat-exchanger system consisting of a bundle of U tubes...

Pillow plate heat exchanger in Thiruvannamalai, Tamilnadu

Pillow Plate Heat Exchangers About Pillow plate heat exchanger : – A pillow plate heat exchanger is commonly used in the dairy industry for cooling milk in large direct-expansion stainless steel bulk tanks. The pillow plate allows for cooling across nearly the entire surface area of the tank, without gaps that would occur between pipes […]

Fan less Cooling Towers in Namakkal, Tamilnadu

Fan less Cooling Towers The name “FAN LESS FILL LESS“ says it all. Devoid of either the fan or the fill media these towers are guaranteed for 100% savings in power & maintenance down time. The special aero dynamic designed FRP / GI louvers minimize spillage and evaporation losses. The Hot Dipped Galvanized structural and […]

Marine Type Heat Exchangers in Sivagangai, Tamilnadu

Marine Type Heat Exchangers About: The Marine Type Heat exchangers are the most common way to cool a boat’s engine, using the lake, river or ocean water in which the boat floats and also there are three methods employed for water-cooled marine petrol and diesel engines. Specifications of Marine Type Heat Exchangers: A water-jacketed exhaust...

Coil Type Heat Exchangers in Trichy, Tamilnadu

Brass Tube Heat Exchanger in Chennai, Tamilnadu

Brass Tube Heat Exchanger Introduction Tipo Brass is usually the first-choice material for many of the components for equipment made in the general, electrical and precision engineering industries. Brass is specified because of the unique combination of properties, matched by no other material, that make it indispensable where a long,...

Multi Cell Cooling Towers Manufacturers in Kumbakonam, Tamilnadu

Multi Cell Cooling Tower Multi Cell Cooling Tower, number of cells and motors can be clubbed together to create multi-cell cooling tower application. By installing multi-cell cooling tower, company can save tremendous power while receiving optimum level of performance. It belongs to the series of Counter-Flow Rectangular Shaped Cooling towers. It...

Floating Heat Exchangers UAE

Floating Heat Exchangers About The Tipo Company actively involved in supplying Floating Heat Exchanger. It is a specially designed heat exchanger in which one end of the tube sheet is fixed to the shell and the other one can freely float inside the shell. It is widely used in applications where there is high stress […]

Copper Heat Exchangers in Thiruppur, Tamilnadu

Copper Heat Exchangers Introduction Tipo Copper Heat Exchangers tubes normally supplied in straight length annealed and half hard temper. The copper tubes shaped by are metal industries have the stiff tolerances but also have the most dependable dimensions throughout tube length. The tube surface is clean both inside and outside with no caustic...

10 TR FRP Cooling Towers

10 TR Cooling Towers Bottle shape Cooling Towers Round shape cooling tower gives 100% cooling efficiencies it’s give good appearance flow rate from 5 M³/Hr To 550 M³/Hr gives differences in temperature 4ºC To30 ºC Availability of Capacities from 5 TR T0 600 TR. Square Shape Cooling Towers Square Shape Cooling Tower or square type […]

Multi Cell Cooling Towers Manufacturers

Multi Cell Cooling Towers Multi Cell Cooling Tower, number of cells and motors can be clubbed together to create multi-cell cooling tower application. By installing multi-cell cooling tower, company can save tremendous power while receiving optimum level of performance. Multi Cell Cooling Towers, belongs to the series of Counter-Flow Rectangular...

Filter Vessels

Filter Vessels We are manufacture, supply, export and distribute Filter Vessels. Used in different industries like chemical, pharmaceutical, petrochemical and heavy duty engineering, our offered vessels are highly acknowledged. Moreover, providing customization facility for these vessels, we have mustered huge client-base. Filter vessel are used in...

Marine Type Heat Exchangers in Madurai, Tamilnadu

Marine Type Heat Exchangers About: The Marine Type Heat exchangers are the most common way to cool a boat’s engine, using the lake, river or ocean water in which the boat floats and also there are three methods employed for water-cooled marine petrol and diesel engines. Specifications of Marine Type Heat Exchangers: A water-jacketed exhaust...

Multi Cell Cooling Towers Manufacturers in Salem, Tamilnadu

Multi Cell Cooling Tower Multi Cell Cooling Tower, number of cells and motors can be clubbed together to create multi-cell cooling tower application. By installing multi-cell cooling tower, company can save tremendous power while receiving optimum level of performance. Multi Cell Cooling Towers, belongs to the series of Counter-Flow Rectangular...

Coil Type Heat Exchangers in Dharmapuri, Tamilnadu

Vertical shell tube heat exchangers in Trichy, Tamilnadu

Vertical Shell and Tube Heat Exchanger Introduction Vertical Shell and Tube Heat Exchanger in which the tubes extend through over sized holes in a liquid distribution plate. Liquid flows through the holes and down each tube exterior surface as a falling film. A spacer or clip, desirably of wire, is placed in each hole around […]

Pressure Vessels Heat Exchanger Coimbatore, Tamilnadu

Pressure Vessel Introduction A pressure vessel is a closed container designed to hold gases or liquids at a pressure substantially different from the ambient pressure. The pressure differential is dangerous and many fatal accidents have occurred in the history of pressure vessel development and operation. Consequently, pressure vessel design,...

Flue Gas Air Pre Heater in Erode, Tamilnadu

Flue Gas Air Pre Heater Introduction Tipo Flue Gas Air Pre Heater of the air preheater is to recover the heat from the boiler flue gas which increases the thermal efficiency of the boiler by reducing the useful heat lost in the flue gas.This flue gases are also sent to the flue gas stack at […]

Double Pipe Heat Exchangers Manufacturers in Viluppuram, Tamilnadu

Double Pipe Heat Exchangers A double pipe heat exchanger, in its simplest form is just one pipe inside another larger pipe. One fluid flows through the inside pipe and the other flows through the annuls between the two pipes. The wall of the inner pipe is the heat transfer surface. The pipes are usually doubled […]

Fan less Cooling Towers in Tirunelveli, Tamilnadu

Fan less Cooling Towers The name “FAN LESS FILL LESS“says it all. Devoid of either the fan or the fill media these towers are guaranteed for 100% savings in power & maintenance down time. The special aero dynamic designed FRP / GI louvers minimize spillage and evaporation losses. The Hot Dipped Galvanized structural and S.S. […]

Copper Heat Exchangers in Sivagangai, Tamilnadu

Copper Heat Exchangers Introduction Tipo Copper Heat Exchangers tubes normally supplied in straight length annealed and half hard temper. The copper tubes shaped by are metal industries have the stiff tolerances but also have the most dependable dimensions throughout tube length. The tube surface is clean both inside and outside with no caustic...

Heat Exchanger Manufacturers in Trichy, Tamilnadu

Heat Exchanger Manufacturers Introduction: Heat exchangers are defined as devices that transfer heat from one liquid or gaseous substance to another in order to change the temperature of the substance for another process. Heat exchangers are constructed with thermally conducted tubes or plates. Heat exchangers are commonly used to transfer...

Kettle Reboiler Type Heat Exchanger in Chennai, Tamilnadu

Kettle Reboiler Type Heat Exchangers Introduction Tipo Kettle Reboiler Type Heat Exchanger is a retaining wall or overflow weir separating the tube bundle from the reboiler section where the residual reboiled liquid called the bottoms product, bundle is kept covered with liquid. Kettle reboilers are reliable in that they can handle high...

Finned Tube Heat Exchanger in Theni, Tamilnadu

Finned Tube Heat Exchanger Finned Tube Heat Exchanger Overview Finned Tube Heat Exchangers for applications that require high heat transfer area for relatively low heat transfer fluids. The advantages of using these are that they are compact. It can be used in refrigeration condensers as well as for oil cooling applications. The typical...

Fixed Tube Sheet Heat Exchanger in Thiruvannamalai, Tamilnadu

Fixed Tube Heat Exchanger Introduction Tipo Fixed Tube Sheet heat exchanger is the most common type heat exchanger in all Industries. It is used in higher-pressure and Higher Temperature applications. Fixed tube Sheet heat exchangers are the one that are very much used in process chemical industries and refinery services, as there is absolutely no...

Brass Tube Heat Exchanger in Coimbatore

Brass Tube Heat Exchanger Introduction Tipo Brass is usually the first-choice material for many of the components for equipment made in the general, electrical and precision engineering industries. Brass is specified because of the unique combination of properties, matched by no other material, that make it indispensable where a long,...

Water Heat Exchangers in Ramanathapuram, Tamilnadu

Water Heat Exchanger Introduction Tipo Water Heat Exchanger heating is thermodynamic process using energy source to heat water above its initial temperature. Typical household uses hot water are for cooking, cleaning, bathing, space heating. In industry, both hot water and water heated to condensation have many uses. Domestically, water is...

Vertical shell tube heat exchangers in Perambalur, Tamilnadu

Vertical Shell and Tube Heat Exchanger Introduction Vertical Shell and Tube Heat Exchanger in which the tubes extend through over sized holes in a liquid distribution plate. Liquid flows through the holes and down each tube exterior surface as a falling film. A spacer or clip, desirably of wire, is placed in each hole around […]

U Tube Heat Exchangers in Salem, Tamilnadu

U Tube Heat Exchangers Introduction U tube heat exchanger is a kind of tube and shell heat exchanger, belongs to the petroleum and chemical equipment. This kind of heat exchanger is named after the‘U’shape tube. U tube heat exchanger is composed of some main components like the tube box, shell, and tube bundle. What’s more, […]

FRP Rectangular Shape Cooling Tower in Coimbatore

FRP Rectangular Shape Cooling Tower Owing to our in-depth domain expertise, Tipo offering a superior quality array of Square Cooling Tower. Our cooling towers are checked on several parameters by quality experts in order to deliver a perfect range from our end. These cooling towers are accessible in different specifications as per the requirements...

Marine Type Heat Exchangers in Coimbatore

Marine Type Heat Exchangers About: The Marine Type Heat exchangers are the most common way to cool a boat’s engine, using the lake, river or ocean water in which the boat floats and also there are three methods employed for water-cooled marine petrol and diesel engines. Specifications of Marine Type Heat Exchangers: A water-jacketed exhaust...

Compressor Cooler in Coimbatore

Compressor Cooler The process of Compressor Cooler produces energy which is manifested as heat. The heat is removed before use (or further compression), hence the introduction of pre cooler, inter coolers and after coolers. TIPO coils offer high quality Compressor Cooler that is highly appreciated for long lasting life and good performance in air...

Pillow plate heat exchanger in Coimbatore

Pillow Plate Heat Exchangers About Pillow plate heat exchanger : – A pillow plate heat exchanger is commonly used in the dairy industry for cooling milk in large direct-expansion stainless steel bulk tanks. The pillow plate allows for cooling across nearly the entire surface area of the tank, without gaps that would occur between pipes […]

Double Pipe Heat Exchangers Manufacturers in Dindigul, Tamilnadu

Double Pipe Heat Exchangers A double pipe heat exchanger, in its simplest form is just one pipe inside another larger pipe. One fluid flows through the inside pipe and the other flows through the annuls between the two pipes. The wall of the inner pipe is the heat transfer surface. The pipes are usually doubled […]

Fan less Cooling Towers in Tutucorin, Tamilnadu

Fan less Cooling Towers The name “FAN LESS FILL LESS“says it all. Devoid of either the fan or the fill media these towers are guaranteed for 100% savings in power & maintenance down time. The special aero dynamic designed FRP / GI louvers minimize spillage and evaporation losses. The Hot Dipped Galvanized structural and S.S. […]

Coil Type Heat Exchangers in Coimbatore

Coil Type Heat Exchangers Introduction Copper tubes are artificial to special requirements as to dimensional tolerances, finish and tempers for use in condensers and heat exchangers. These copper heat exchanger tubes are normally supplied in straight length in annealed & half hard temper. The copper tubes shaped by are metal industries not only...

Closed Circuit Cooling Towers in Madurai, Tamilnadu

Closed Circuit Cooling Tower Introduction Closed circuit cooling towers provide evaporative cooling for many types of systems, and the specific application will largely determine which BAC Closed Circuit Cooling Tower is best suited for a project. This isolates the process fluid from the outside air, keeping it clean and free of contamination in a...

Air Cooled Heat Exchanger in Madurai, Tamilnadu

Air Cooled Heat Exchanger Introduction Air-cooled heat exchangers are generally used a process system generates heat which must be removed, but for which there is no local use. A good example is the radiator in your car. The engine components must be cooled to keep them from overheating due to friction and the combustion process. […]

Air Cooled Heat Exchanger in Thiruvallur, Tamilnadu

Air Cooled Heat Exchanger Introduction Air-cooled heat exchangers are generally used a process system generates heat which must be removed, but for which there is no local use. A good example is the radiator in your car. The engine components must be cooled to keep them from overheating due to friction and the combustion process. […]

Air Cooled Heat Exchanger in Dindigul, Tamilnadu

Air Cooled Heat Exchanger Introduction Air-cooled heat exchangers are generally used a process system generates heat which must be removed, but for which there is no local use. A good example is the radiator in your car. The engine components must be cooled to keep them from overheating due to friction and the combustion process. […]

Air Cooled Heat Exchanger in Salem, Tamilnadu

Air Cooled Heat Exchanger Introduction Air-cooled heat exchangers are generally used a process system generates heat which must be removed, but for which there is no local use. A good example is the radiator in your car. The engine components must be cooled to keep them from overheating due to friction and the combustion process. […]

M	T	W	T	F	S	S
				1	2	3
4	5	6	7	8	9	10
11	12	13	14	15	16	17
18	19	20	21	22	23	24
25	26	27	28	29	30	31

Tags: Marine Heat Exchanger

Varuthiangara Palayam, Seth Narang Das Layout, Tatabad,Coimbatore, Tamil Nadu 641009

+91 63790 03383 +91 99421 79413

info@tipoheatexchangers.com

Varuthiangara Palayam,
Seth Narang Das Layout,
Tatabad,Coimbatore,
Tamil Nadu 641009

+91 63790 03383
+91 99421 79413